How to Use TaoTronics Humidifier

drops of essential oil and place the lid back on. Connect to a power source and the device will enter standby mode. You will then hear a beep sound and the buttons on the control panel will light up in red.

How to Use TaoTronics Humidifier

  1. When placing the tank lid back on, align the notches on the lid with the bulges on the tank.
  2. In standby mode, the LED display will dim to half of the brightness if there is no operation in 3 seconds. Tap any button to resume the brightness.

How to Turn On / Off the Mist?

  1. Tap the Power Button once to start mist output (default: medium level). The Power Button will turn green.
  2. Tap again to stop output.

How to Adjust Light on TaoTronics Humidifier?

  1. Tap the Light Button to enter color carousel mode, which will automatically cycle through different color choices.
  2. Tap again to stay on the current color. Keep tapping to cycle through different colors. After cycling through all colors, tapping the Light Button again will return to color carousel mode.
  3. Tap and hold the Light Button for 1.5 seconds to turn off the light.

Memory Function If power was not disconnected, the humidifier will remember the mist setting from the time it was last turned off.

How to Remote Control TaoTronics Humidifier?

  1. All buttons on the remote control function the same way as on the humidifier.
  2. Aim the remote control at the LED display of the humidifier for better response.
  3. The effective range between the remote control and the product is 4 meters / 157.5 in.

How to Do Cleaning and Maintenance for TaoTronics Humidifier?

  1. Fill the water tank half full, and add in 100ml white vinegar. Run the humidifier for 5-10 minutes to allow the vinegar/water mixture to work through and loosen up the gunk.
  2. Turn off the humidifier, unplug it, and drain the water. Cover the air outlet with the protection cap, then wipe out the inside of the diffuser with the included cleaning brush.
  1. Pay special attention to clean the water level sensor, as it often causes the most issues when it gets dirty. You can use a drop of lemon essential oil on your brush or q-tip if you need to cut through extra grime. (Be extra careful when you drain water to avoid water getting into the underside or motor area to ruin the product).
  2. Use a soft cloth to wipe down the outside of the machine to remove any fingerprints, smudges, etc. The cloth can be dampened with water, or you may lightly spray it with a bit of gentle cleaner or vinegar/water solution.
  3. Clean the humidifier once a week.

How to Install the Floater on TaoTronics Humidifier?

  1. Insert the mist tube into the hole on the base of the humidifier.
  2. Rotate it to lock in place.
  3. Put the floater into the mist tube with the UP side facing up.
  4. Align the hole on the lock with the bugles on the mist tube to lock in place, make sure the convex side is facing up.

How to Adjust the Fan Mode on TaoTronics Humidifier?

Rotate the Control Knob to set the fan between quiet and standard modes.

How to Clean or Change the Filter?

If - It is hard and crusty - It develops an odor - Moisture output is decreased

How to Clean and Disinfect the Filter?

  1. Soak the filter in vinegar first for easier cleaning. Apply household detergent when needed. Wash it once a week.
  2. Soak the washed filter in 100℃ boiled water for 10 minutes and expose it to strong sunlight to disinfect.

How to Clean the Water Tank?

  1. Wipe the water tank with a dump soft cloth or the included cleaning brush. Rinse it with clean water.
  2. Rotate the Water Outlet Cap clockwise to remove it and take out the rubber seal to drain water.

Note：Please drain water inside the tank when not using the humidifier for a long time.

What are the Safety Instructions BEFORE USING THE HUMIDIFIER?

  1. Please extend the cord and check any signs of damage. Do not use the humidifier if the cord has been damaged.
  2. DO NOT place this humidifier in wet environments.

Please always keep the humidifier out of reach of patients & children & pet.

  1. Please always place the unit on a smooth, flat, lint-free, non-metallic, waterproof and level surface and keep it away from direct sunlight.
  2. Always place the unit 2 feet (60 cm) above the floor, 12 inches (30 cm) away from the wall, other appliances or wooden furniture.
  1. DO NOT place the unit on carpet, towel or wood surface, which will block the vent and may damage the unit.
  2. DO NOT place the humidifier near naked flames and heat sources, such as stove tops, ovens, radiators or computers.

What are the Safety Instructions WHEN USING THE HUMIDIFIER?

  1. DO NOT plug the unit with wet hands.
  2. DO NOT direct the mist nozzle against the wall.
  1. DO NOT use your hand or any other object to cover the nozzle while the unit is on to avoid damaging the product or causing injury.
  2. DO NOT clean the unit while it is connected to a power source or while it is on.
  1. DO NOT move or tilt the humidifier while it is in operation.
  2. The most comfortable environmental humidity is between 40%-60%. Please adjust the mist as

What are the Safety Instructions AFTER USING THE HUMIDIFIER?

  1. Always disconnect from a power source by pulling the plug when not in use.
  2. Humidifier requires regular cleaning. Please refer to, and follow the Cleaning and Maintenance instructions.
  1. DO NOT clean the humidifier right after turning it off if the humidifier has been working for a long time. Allow the humidifier to completely cool down before cleaning.
  2. DO NOT attempt to repair or adjust any electrical or mechanical functions on this humidifier. Doing so will void your warranty.

How to Add Water to TaoTronics Ultrasonic Cool Mist Humidifier?

Add Water to TaoTronics Ultrasonic Cool Mist Humidifier

  1. Remove the nozzle and turn the water tank upside down.
  2. Remove the tank cap and fill the tank with clean and cool water only.
  3. Attach the tank cap and place the tank back onto the base. Make sure it fits together securely so that water can go from the tank to the reservoir. Put the nozzle back on.

Notes:

  1. If tap water is too hard, it is recommended to use filtered or distilled water to avoid white DO NOT use hot water.
  2. DO NOT add any essential oils or medicinal tablets into the water tank.
  3. DO NOT add water into the base or through nozzle.
  4. DO NOT move the humidifier while the water tank is full of water to avoid leakage or base

How to Power ON/OFF TaoTronics Ultrasonic Cool Mist Humidifier?

  1. Press the Power Button once to enter medium level misting by default. The LED display will show the mist level and environment humidity level.
  2. Press again to stop misting, the fan will continue working for 5 minutes to dry the mist tube

How to Adjust Mist on TaoTronics Ultrasonic Cool Mist Humidifier?

When the unit is on, press the Mist Button to adjust the mist between low / medium / high levels.

How to Set Timer on TaoTronics Ultrasonic Cool Mist Humidifier?

Press the Timer Button to set the timer from 1 hour to 24 hours, the timer will flash three times to confirm your setting. Once set, the LED display will show the countdown timer and the environment humidity level alternately. When time is up, the unit will automatically turn off.

How to Switch Nightlight / Sleep Mode on TaoTronics Ultrasonic Cool Mist Humidifier?

  1. Press the Nightlight Button / Sleep Button once to turn on the nightlight.
  2. Press it again to enter sleep mode with the mist level switching to low level. All the indicators on the LED display will turn off except the sleep indicator.
  3. If no operation is done in 3 seconds under Sleep Mode, the sleep indicator will turn off Press any button to activate Sleep Mode (with the sleep indicator on). All the other buttons remain functional.
  4. Press one more time to exit sleep mode.
  5. When there is no enough water inside the water reservoir under Sleep Mode, the humidifier and the LED display will turn off automatically.

How to Set Humidity Level on TaoTronics Ultrasonic Cool Mist Humidifier?

  1. Press the Humidity Button to set the humidity level from 30% to 95% with an increase / decrease of 5% in each tap.
  2. The humidity level set will flash three times to confirm your setting.
  3. The unit will stop misting once the environment humidity reaches the preset humidity level and resume misting once the environment humidity level is below the preset level.
  4. To exit the humidity setting, press the Humidity Button one more time when humidity is set to 95% or restart the unit.

Note: The most comfortable environmental humidity is between 40%-60%. Please adjust the mist as needed.

How to Clean and Maintain TaoTronics Ultrasonic Cool Mist Humidifier?

  1. DO NOT submerge the base in water.
  2. Make sure water does not enter the base through the air outlet, air inlet, or the control buttons and LED display.
  3. DO NOT wash any part of this humidifier in dish washer which will damage the humidifier and void the warranty.

Turn off the humidifier, unplug it from the power source. Drain water from the tank, reservoir and base.

  1. To properly clean your humidifier, we recommend you to remove scale and disinfect the humidifier separately.
  2. DO NOT mix vinegar and bleach solutions together. Do not use more than 1 tsp. of bleach per gallon of water to avoid damaging your humidifier.
  3. Please make sure the rubber ring & rubber cap & spring on the tank cap is installed properly after cleaning to avoid water leakage.

How to Remove Scale from TaoTronics Ultrasonic Cool Mist Humidifier?

  1. Turn off and unplug the humidifier. Remove the nozzle.
  1. Remove the water tank from the base. Remove the tank cap. Make sure that the white sealing ring does not come off. Drain water from the water tank and base. Remove any accessories and set aside.
  1. Fill the water tank half full. Add in 1 teaspoon of undiluted distilled white vinegar. Attach the tank cap and shake for 15 seconds.
  2. Place the tank onto the base. The vinegar solution will enter the water reservoir to loosen mineral buildup (scale) on the atomizer, water floater and the bottom of the water tank. Set still for 15-20 minutes.
  3. Uncap the tank cap and drain the solution. Wipe the atomizer and floater with a soft cloth to remove loosened mineral deposits.
  4. Rinse both the water reservoir and water tank until the smell of vinegar (for scale removal) or bleach solution (for disinfecting, see below) is gone.

How to Disinfect TaoTronics Ultrasonic Cool Mist Humidifier?

  1. Follow steps 1-2 of the previous section on scale removal.
  2. Fill the water tank half full. Add in ½ tsp of bleach. Place the tank cap back on. Swish the solution around in tank. Place the tank on the base. The bleach solution will enter and disinfect the water reservoir as well as the other components. Set still for 15-20 minutes.
  3. Follow steps 4-6 of the previous section on scale removal to complete disinfecting the

How to Clean the Dustproof Sponge of TaoTronics Ultrasonic Cool Mist Humidifier?

Clean the Dustproof Sponge of TaoTronics Ultrasonic Cool Mist Humidifier

Clean the dustproof sponge (at the bottom of base) with water or detergent once a month. Put it back in place after cleaning.

End-Of-Season Care and Storage

  1. Follow the cleaning instructions when the humidifier will not be used for at least one week, or at the end of the season. Remove any accessories used with the humidifier and allow the humidifier and accessories to dry completely before storing.
  2. DO NOT store with water inside the base, water reservoir, or tank.
  3. Pack the unit safely and store in a cool, dry location.

How to Add Water to TaoTronics Top Fill Humidifer?

Add Water to TaoTronics Top Fill Humidifier

  1. Remove the tank cover, take out the water tank by holding the tank handle.
  2. Fill the tank with clean water.
  3. Place the tank back into the base, cap on the cover. Please make sure it fits together securely so that water can go from the tank to the reservoir.
  4. Connect to an appropriate power source. The unit enters standby mode with a beep sound, the LED display shows the relative humidity of current environment.

  1. If tap water is too hard, it is recommended to use filtered or distilled water to avoid white DO NOT use hot water.
  2. DO NOT add any essential oils or medicinal tablets into the water tank.
  3. DO NOT add water into the base or through nozzle.
  4. DO NOT move the humidifier while the water tank is full of water to avoid leakage or base overfilling.
  5. You can fill the water tank without removing it from the base, pay attention to avoid water getting into the air outlet.

How to Adjust Warm Mist?

Tap the Warm Mist Button to adjust the heat level between high / medium / low levels. When the heat level is at high level, tap the Warm Mist Button one more time to turn off the heating. The corresponding warm mist level indicator on the LED Display will light up.

How to Set High Temperature Alarm?

High temperature alarm will be activated if temperature of the heat tube is too high, 8 beep sounds will be heard every other second. The unit will stop working after 1 minute. Caution: Unplug the power source and wait for 3 minutes to allow the unit to cool down before you turn it on again.

How to Remove Scale from TaoTronics Top Fill Humidifier?

  1. Turn off and unplug the humidifier.
  2. Remove the tank from the base and drain water according to the indicated position.
  3. Fill the water tank half full. Add in 1 teaspoon of undiluted distilled white vinegar. Use a soft cloth to wipe the tank thoroughly.
  4. Place the tank onto the base. The vinegar solution will enter the water reservoir to loosen mineral buildup (scale) on the atomizer, water floater and the bottom of the water tank. Set it still for 15-20 minutes.
  5. Uncap the tank cap and drain the solution. Wipe the atomizer and floater with a soft cloth to remove loosened mineral deposits.
  6. Rinse both the water reservoir and water tank until the smell of vinegar (for scale removal) or bleach solution (for disinfecting, see below) is gone.

How to Use Essential Oils for Baby Room Nursery?

Please be sure to follow our recommendations on how to use essential oils for baby room nursery with your humidifier. Failure to do so may result in malfunction or damage to the humidifier or even harm to the babies.

Younger children or babies have super sensitive skin. The thin, sensitive skin is much more permeable to essential oils than the skin of an older child or adult. Too high a dilution could cause skin irritation and other problems later down the road. Therefore, before applying essential oils to babies, it’s important to understand proper dilution ratios and application methods.

Even when essential oils are diluted with a carrier oil, they may cause skin irritation and sun sensitivity, especially in children. It’s recommended that a patch test (also sometimes called a “spot test”) be performed on the skin, with each new oil introduced.

How to Test Your Baby’s React to the Oil?

  1. Apply a very small amount of diluted essential oil on your baby’s skin on the leg or on the
  2. Wait for about 24 hours and check for any signs of irritation, redness or inflammation of the
  3. If you notice a reaction, stop using that particular oil. If your baby has no reactions, then you can proceed using that oil.

Safety Tips for Babies /Children

Essential oils need to be used with proper care and precautions to avoid any risks. We recommend to limit diffusion to 30-60 minutes, a few times a day as needed.

How to Add Water to Humidifier for Babies?

Add Water to Humidifier for Babies

  1. Turn the water tank upside down. Remove the tank cap and fill the tank with clean and cool water only. [Optional] Add diluted aromatherapy-grade essential oils into the tank, if you use the humidifier for baby room nursery, please read the【INFORMATION ON USE OF ESSENTIAL OILS FOR BABY ROOM NURSERY】
  2. Attach the tank cap and place the tank back onto the base. Please make sure it fits together securely so that water can go from the tank to the reservoir.
  1. If tap water is too hard, it is recommended to use filtered or distilled water to avoid white DO NOT use hot water.
  2. DO NOT put anything other than water or diluted essential oil into the water tank.
  3. DO NOT add water into the base or through nozzle.
  4. DO NOT move the humidifier while the water tank is full of water to avoid leakage or base

How to Power On/Off and Adjust Mist on TaoTronics Humidifier for Babies?

Connect the power adapter to humidifier input port and plug the adapter into a wall socket. Now the humidifier is ready for use.

  1. Rotate the control knob clockwise to the ON position. The LED indicator will light up, indicating the humidifier has been turned on to a minimum mist level.
  2. Keep rotating the control knob clockwise to increase the mist level.
  3. Rotate the control knob counterclockwise to the OFF position to turn off the humidifier. The LED indicator will turn off. The fan will work for another 2 minutes to dry the mist tube.
  4. The most comfortable environmental humidity is between 40%-60%. Please adjust the mist as needed.

How to Set Nightlight Control on TaoTronics Humidifier for Babies?

  1. Press the button to turn on/off the nightlight, the brightness is at the default medium range.
  2. Press and hold the button for 1.5 seconds to adjust the light brightness, release at the desired level. Press and hold it again to adjust the brightness to the opposite direction.
  3. The nightlight has memory function, If power is not disconnected, the unit will remember the brightness setting of the last time when the nightlight or humidifier was turned off.